SpeedyBee Master 5 V2 frame

Features:

• The Master 5 V2 is designed for both kinematic and freestyle flying. Thanks to the advanced Deadcat geometry, the flight control is closer to the center of gravity than in most other DC frames;
• Innovative vibration damping design reduces the impact of motor noise on the gyroscope, creating a more stable working environment. With an average of only 1.5 screws per leg, the quick-mount design allows for easy assembly and disassembly of the frame;
• The honeycomb-shaped CNC-machined aluminum alloy front part of the drone provides more strength and aesthetic appearance. The 130° H-FOV (horizontal field of view) provides a wider field of view at the front of the drone. In addition, when the DJI O3 Air Unit system is installed, the frame supports ND filters and the attachment of an interchangeable side plate.
• TPU side plate, located in the CNC part, helps to dampen camera vibrations. Pilots can modify it according to their needs to accommodate more mounting holes and eliminate the darkening effect at the edges for a clearer image.

Specification:

• Frame: Master 5 V2;
• Wheelbase: 226 mm;
• Weight: About 140 g (without 3D printed parts);
• Top plate thickness: 2.5 mm (T300 3K);
• Middle panel thickness: 2 mm (T300 3K);
• Bottom plate thickness: 2.5 mm (T300 3K);
• (hand) thickness: 5 mm (T300 3K);
• Chamber side panel thickness: 2 mm (TUPC material);
• Vibration damping construction hardness: Yellow HB80, transparent HB50;
• 3D printed parts: Yellow TPU;
• Motor retainer gap: Φ8 mm;
• Compatible propellers: 5-5.1 inches;
• Motor mounting holes: 16×16 mm;
• Flight controller (FC) mounting holes: 30.5×30.5 mm (M3) and 20×20 mm (M3);
• Drone front: 7075 CNC machined aluminum alloy;
• Aluminum supports: 7075 M323mm (6mm / 4.7mm), M323mm (4.6mm);
• Internal installation height: 23–30 mm;
• Standard antenna mounting support: SMA (single), O3 4 mm, RunCam Link;
• Standard GPS base dimensions: 18×18×8 mm (an additional holder is required for other sizes);
• Rear bracket mounting holes: 20×20 mm, 25.5×25.5 mm, 30.5×30.5 mm;
• Removable stand protection plate with RGB LED: Included
• Motor wiring protection: Included;
• 3D printed parts included in the kit:
GoPro mount;
Capacitor/sound signal holder;
Hand protection;
181 GPS base;
T-shaped antenna bracket;
TPU protection for the front of the CNC drone;
Camera vibration reduction module;
• Buzzer: TMB12A05.

Package:

1x CNC front part;
1x Left and right side of the frame;
1x Frame parts set;
1x Camera side plate;
2x 23 mm aluminum spacers (left + right);
2x 23 mm aluminum stair spacers;
1x 3mm non-slip battery pad (left + right);
1x General cooling pad;
1x TPU mount for receiver;
1x 8-pin cable;
1x Vibration damping pad for frame (clear 50A and yellow 80A);
2x Cable glands;
1x 0.5 mm bottom protective pad.

3D printed parts:

1x GoPro mounting base;
1x Antenna base (left + right);
1x SMA antenna mounting base;
1x DJI O3 Air Unit antenna base;
1x 181 GPS base;
1x Capacitor and buzzer base;
4x Leg guards (on the levers);
1x CNC rear guard.

Other parts:

1x Frame side panels (left + right);
4x Motor cable sleeves;
4x LED light tubes;
1x Signal sound signal (buzzer);
1x Red and black cable (100 mm);
2x 250 mm fastening strap.

Screws and fasteners:

3x 11 mm M3 flat head hex screw;
9x 6 mm M3 flat head hex screw;
7x 5 mm M3 flat head hex screw;
5x M1.6*8 dome head hex bolt;
5x 8 mm M2.5 hex screw;
5x 3mm M2 dome head hex screw
3x 8 mm M2 hex screw;
3x 6 mm M3 dome head hex screw;
9x 10 mm M3 dome head hex screw;
10x 8 mm M3 dome head hex screw;
5x 14 mm M3 flat head hex screw;
1x 20mm M5 screw;
4x 4 mm M3 purple aluminum alloy nut;
1x M5 self-tightening nut;
4x 24 mm M3 dome head hex screw;
5x 4 mm M2 dome head hex screw;
3x 6 mm M2.5 hex head screw;
5x 7mm M3 dome head hex screw.